addon.pathtools.cornerSet and cornerRemove now refuse a key other than
id and anchors in an `items` member, with the standard unknown-parameter
error, instead of ignoring it. A misspelled `anchor` used to fall back
to the request's `anchors`, else the path's direct-selected anchors,
else every corner of the path. They also refuse `items` given together
with `ids`, which `items` replaces. Saved steps played with replay
still run as recorded.
Docs: docs/mcp.md, docs/target-app-parity.md.
Add Points and Divide into Dashes read each subpath's selected segments
with a range lookup in the path's ordered segment set instead of
filtering the whole set once per subpath. Add Points at Crossings and
Split at Crossings sort a path's crossing places into a list per
subpath once, in the order they come, instead of filtering the whole
list for every subpath. Places on a subpath that no longer exists are
still left out. The results are unchanged.
Tests cover paths with several subpaths, an empty subpath, an
untouched subpath and selection on the last subpath, for all four
commands, plus the anchor fallback and the grouping of out-of-order
crossing places.
- The clipping path of a clip group or a clipped layer takes no part,
the members of a compound clipping path included. Before, only a
plain clipping path was left out.
- In isolation mode only paths inside the isolated object are trimmed;
paths outside it still count as crossing.
- A rectangle or line that reaches so many paths that comparing their
boxes would take more than 50,000,000 tests is refused before any
work starts.
- A tool drag that goes 3 screen pixels or more from the press stays a
rectangle or line when it ends near the press. Before, it ran as a
click and could remove a whole path the final rectangle did not
touch.
Docs: docs/mcp.md.
The new Trim at Crossings Tool removes stretches of paths between the
places where they are crossed by another path or by themselves. A click
removes the stretch under the pointer, a drag removes every stretch its
rectangle touches, and an Alt-drag removes every stretch its freehand
line crosses. It works on every path that can be edited, selected or
not, and each gesture is one undo step.
- `addon.pathtools.trim {at, tolerance?}`, `{rect}` or `{points}` is the
command behind the tool. A closed path that loses a stretch becomes
open, an open path that loses a middle stretch becomes two paths with
its appearance in its place in the stacking order, and a path that
nothing crosses is removed whole. The stretches that stay get no new
anchors.
- Hidden and locked paths, guides and clipping paths are not trimmed and
do not count as crossing. Only the paths the gesture reaches are
searched for crossings, and one work limit covers every path the
command trims.
- `crossings_on` and `crossings_on_within` in `vectorcraft-pathops` find
the crossings on one path and compare it only with the segments in
its box.
- The new tool shares the crossing search with Add Points at Crossings
and Split at Crossings, so those change too: two segments of a path
that meet at an anchor, directly or across segments with no length,
now count as crossing where they cross again away from that anchor,
and do not count as crossing at the anchor itself. With Self
Crossings, a curved segment that loops over itself counts as crossing
itself. Before, both crossings were missed.
- The tool is an add-on tool: Object › Plug-ins › Path Precision Tools
and the All Tools drawer list it, it has no shortcut, and neither
shipped toolbar shows it.
Docs: docs/mcp.md, docs/ui-parity.md, docs/target-app-parity.md.
The params docs now state the direction (and the zero) of each angle or
rotation a command takes; behaviour is unchanged. Shape creation, text.create,
the grids, add-on shapes, saved views, Liquify, Puppet Warp pins, Mirror and
Radial Repeat and Vector Halftone turn clockwise; text character rotation,
gradients, the eraser tip and print screen angles turn counter-clockwise.
view.saved.new's rotation note changes its schema, so the API level goes to 3.
A test walks every command's params doc and fails when a param named like an
angle or rotation doesn't say clockwise or counter-clockwise.
addon.pathtools.cornerSet takes `every` ("all", "odd" or "even"; default
"all"), which keeps, of the anchors already chosen (named, direct-selected
or all), only the odd- or even-numbered ones, counted along each path from
its first anchor as number 1. Anchors that take no corner still count, so
the pattern follows the path's anchor order on open and closed paths; when
nothing is left the command says so. Unknown values are refused.
Object › Plug-ins › Path Precision Tools › Set Corners… (also a button in
the Anchor Inspector's Corners section) opens a dialog with Radius, Corner
kind and Anchors (All / Odd-Numbered / Even-Numbered) that previews on the
canvas and commits as one undo step.
addon.pathtools.divideDashes cuts the selected paths (or only their
direct-selected segments) into separate open paths of a dash length
measured along the curve, with an optional gap (gap pieces dropped
unless removeGaps is false) and Fit to Corners and Ends; pieces keep
the path's appearance, one undo step, at most 100000 pieces. Geometry
in vectorcraft-pathops; dialog with unit fields and Preview; tests,
sweep cases, catalog rows and docs.
Path Precision Tools gains the Shared Edge Merge Tool, kept out of the
toolbars (All Tools drawer and Object › Plug-ins › Path Precision Tools,
no shortcut), and Keep Shared Points Together:
- Shared Edge Merge Tool (sharedEdge): over two paths touching at two
coincident anchors (tolerance 0 to 3 pt) hovering shows the two
stretches and the merged edge; a click replaces both with it, half way
between them, or following the upper (Shift) or lower (Alt) path. Both
paths stay closed or open, anchors either stretch has inside are
matched on the other, one undo step.
- Making ends: near anchors meet on a click and an anchor one path lacks
is added to match; Shift+Alt asks for this inside a stretch.
- Keep Shared Points Together: an option that makes Slide Anchor Along
Path, Extend Path and Set Anchor take coincident anchors along. Nothing
else in the app changes.
- Shared Edges section in the Anchor Inspector: brush diameter,
coincidence and the option.
- Commands addon.pathtools.mergeEdge and movePointsTogether, params
validated and covered by the command sweep.
- Cursor stand-in, catalog rows in every language, docs and tests.
Path Precision Tools gains two tools, kept out of the toolbars (All Tools
drawer and Object › Plug-ins › Path Precision Tools, no shortcuts):
- Corner Tool (cornerTool): editable corners on any path through the
existing Live Corners. Hover shows an eligible anchor, a click cuts a
corner with the tool's radius and kind, a drag sizes it (Shift: whole
values), a corner's marker selects it and loads its values, resizes it
and removes it at 0 or on a double-click; a corner never grows past
what fits; an Alt-marquee cuts every eligible anchor inside.
- Corners section in the Anchor Inspector: radius, kind, selected count,
Apply to Selected Anchors.
- Slide Anchor Along Path (slideAnchor): a drag runs an anchor along its
curve, the neighbouring segments refitted by the keep-shape kernel;
Shift snaps where the tangent is a multiple of 45° from the constrain
angle.
- Commands addon.pathtools.cornerSet, cornerRemove and slideAnchor, one
undo step each, params validated and covered by the command sweep.
- Cursor stand-ins, catalog rows in every language, docs and tests.
Path Precision Tools gains the Parametric Shape Tool: ten kinds of shape
(rectangle, ellipse, polygon, star, ring, arrow, cross, heart, gear,
speech bubble) that stay editable as numbers.
- Geometry in vectorcraft_pathops::addons::pathtools::shapes: each kind's
outline, corner rounding limited to the middle of a side, a fingerprint
of the outline, recovery of centre, size and rotation after a move,
turn or scale, and recognition of plain rectangles, ellipses and
regular polygons.
- The tool (parametricShape, All Tools drawer and Object › Plug-ins ›
Path Precision Tools only, no shortcut): drag from the centre (Shift:
45° steps), arrow keys change the count and values while dragging,
handles edit a selected shape, double-click places one.
- Commands addon.pathtools.shape.create / .set / .convert, one undo step
each; params checked (counts 3..1000, sizes up to 16384 pt).
- A shape keeps its numbers in one object-data entry (vc-pathtools-shape)
that SVG export already leaves out; anchor edits make it a plain path.
- Parametric Shape panel, cursor stand-in, catalog rows in all 25
languages, docs and tests.
A built-in add-on under Object › Plug-ins › Path Precision Tools:
- Anchor Eraser Brush: painting over selected paths removes the anchors
under the brush that the outline can do without within a tolerance,
refitting the handles beside them (Alt ignores the tolerance, Cmd/Ctrl
deletes without refitting, pen pressure can scale the brush); one undo
step per stroke.
- Extend Path tool: dragging an end of an open path carries it on
straight, by stretching its last curve or along the circle it curves
on, or shortens it back along itself.
- Measure & Inspect tool: drag to measure distance and angle; hover a
path to read segment and path length, area, curvature, tangent and
anchor angles and handles, in the document's units.
- Anchor Inspector panel: the selected anchor's position and handles as
numbers, with Make Smooth (auto-smooth rule), Make Corner, Equalize
Handles, Remove Points Keep Shape, Add Points and three ways to close.
- Add Points at Crossings and Split at Crossings.
The tools stay out of both toolbars as shipped; the All Tools drawer
lists them under the add-on's heading. Commands are addon.pathtools.*;
the existing commands, tools and menus are unchanged.
dotCooCoo